4th July Sale. Buy 2 Windows, Get 1 FREE.

Mon – Fri: 9 Am – 5:30 Pm
How to calculate the pitch of a roof (formula + degree chart)

How to Figure a Roof Pitch

Roof steepness affects drainage, material choices, and replacement estimates. You can measure it using a level and tape measure, suitable building plans, or a digital angle finder.

Understanding how to figure a roof pitch starts with comparing vertical rise to horizontal distance. The methods below explain where to measure and how to convert your result.

What is roof pitch?

Roof pitch usually describes how much a roof rises over a horizontal run of 12 in. A 6:12 roof rises 6 in. for every 12 in. measured horizontally.

Run is the horizontal distance beneath the incline. Measuring along a sloping rafter gives its diagonal length, which cannot replace run in the calculation.

For a symmetrical gable roof, the run from the wall to the ridge centerline equals half the corresponding wall span. Unequal roof sections require separate measurements.

how to figure a roof pitch

Traditionally, pitch means rise divided by the full span, while slope means rise divided by run. Modern residential discussions often use both terms for the familiar rise:12 measurement.

Record the ratio explicitly when requesting an estimate. Writing “6:12” avoids confusion between a fractional pitch, an angle, and a percentage.

How to calculate the pitch of a roof

Choose a method based on the access and information available. An accessible attic or accurate construction drawing can provide measurements without stepping onto the roof.

Learning how to calculate the pitch of a roof requires keeping your horizontal and vertical measurements separate. Use matching units and check the result at another location on the same roof plane.

Method 1: Measure with a level and tape

Measure beneath an accessible attic rafter with a level and tape measure. Use this method only where secure flooring or a suitable platform allows you to reach the framing.

Do not step on ceiling drywall or insulation that conceals unsupported areas. If access requires balancing on framing, arrange a professional measurement.

Gather the following equipment before entering:

  • Level: Use a straight spirit level with a clearly marked 12 in. reference point.
  • Tape measure: Choose a readable tape for measuring the vertical gap.
  • Lighting: Bring a flashlight or work light so framing and footing remain visible.
  • Record sheet: Note the measurement location, rise, and run for each roof section.

Position yourself beneath a straight section of a common rafter. Avoid diagonal hip or valley rafters because their inclination differs from the roof plane.

  1. Mark the run: Identify a point 12 in. from the end of the level that will touch the rafter.
  2. Position the level: Touch that end to the rafter’s underside and extend the level horizontally toward the ridge.
  3. Center the bubble: Adjust the tool until it is horizontal, maintaining contact at the starting end.
  4. Measure the rise: Measure vertically upward from the marked point to the rafter’s underside, using the same level edge as your baseline.
  5. Record the ratio: A 5 in. gap over the 12 in. horizontal distance means a 5:12 slope.

Repeat the measurement nearby to check consistency. A bowed rafter, misplaced tape, or tilted level can change the reading.

Method 2: Use a digital angle finder

Use a digital angle finder against the underside of an accessible common rafter. This method gives an angle that you can convert into a rise:12 ratio.

Check the tool against a known horizontal surface first. Confirm that its display measures inclination from horizontal, since a reading referenced to vertical describes a different angle.

Hold the measuring edge flush against straight framing and record the result. A reading near 26.57° corresponds to 6:12.

A phone inclinometer can provide an estimate, but its case, camera bump, and calibration may affect contact and accuracy. Repeat the reading and verify important measurements with another method before ordering materials.

Method 3: Calculate from building plans

Calculate the ratio from a dimensioned roof section or framing drawing. Find the vertical rise and corresponding horizontal run between matching reference points.

For example, a symmetrical gable with a 24 ft wall span has a 12 ft run to its centerline. If the corresponding rise is 6 ft, the roof is 6:12.

Confirm that the drawing reflects the current building. An addition, altered ridge, or rebuilt porch may differ from the original plans.

Use labeled dimensions instead of measuring a drawing displayed on a screen. Resizing or printing can change its scale.

how to calculate the pitch of a roof

Roof slope formula

Divide the vertical rise by the horizontal run to express steepness as a decimal. Multiply that result by 12 to obtain the first number in a rise:12 ratio.

The roof slope formula is:

Pitch=RiseRun12

For a measured rise of 30 in. over a horizontal run of 72 in., the calculation is 30 ÷ 72 × 12 = 5. The resulting ratio is 5:12.

Keep measurement units consistent

Both measurements must use the same unit before division. Convert 3 ft to 36 in. if your other measurement is recorded in inches.

Metric measurements work equally well because the units cancel. A 150 cm rise over a 300 cm run produces 0.5 × 12 = 6, or 6:12.

Calculate slope percentage

To express the same incline as a percentage, multiply Rise ÷ Run by 100. A 6:12 roof therefore has a 50% slope.

A 50% slope is not 50°. Percentage compares distances, while an angle measures rotation from horizontal.

Keep the original measurements in your notes alongside the converted result. This lets a contractor check your calculation without guessing which units you used.

Roof pitches in degrees

An angle describes the roof’s inclination above a horizontal line. Converting the ratio is useful when comparing drawings, angle finder readings, and product specifications.

Expressing roof pitches in degrees uses the inverse tangent function, written as arctan or tan⁻¹. Set your scientific calculator to degree mode before entering the calculation.

Angle=RiseRun

For 6:12, divide 6 by 12 to get 0.5. Applying arctan gives approximately 26.57°.

Conversion chart

The chart lists whole-number ratios from 1:12 through 12:12, plus 2 steeper examples. Values are rounded to 2 decimal places.

Rise:RunAngleSlope
1:124.76°8.33%
2:129.46°16.67%
3:1214.04°25.00%
4:1218.43°33.33%
5:1222.62°41.67%
6:1226.57°50.00%
7:1230.26°58.33%
8:1233.69°66.67%
9:1236.87°75.00%
10:1239.81°83.33%
11:1242.51°91.67%
12:1245.00°100.00%
16:1253.13°133.33%
18:1256.31°150.00%

A search for “calculate pitch of roof degrees” may also return tools that convert angles back into ratios. Check the conversion direction before entering your measurement.

To reverse the calculation, multiply tan(angle) by 12. For example, tan(22.62°) × 12 gives approximately 5, confirming a 5:12 ratio.

Common roof pitch

Residential roofs vary with architectural style, building dimensions, and regional construction practices. There is no universal ratio that suits every house or roofing material.

A common roof pitch example is 6:12, with 4:12 and 5:12 also familiar residential configurations. These examples help you interpret measurements without establishing what your own roof should be.

roof pitches in degrees

Match the covering to the incline

Material suitability depends on the particular roofing system. Many asphalt shingles can be installed at 2:12 or greater, with special underlayment provisions below 4:12.

Below 2:12, consider a roofing system specifically approved for that incline. Metal roofing requirements vary by panel design, seam construction, and installation details.

Check the chosen product’s instructions before comparing prices. A covering suitable for the main roof may not suit a shallower porch.

Account for the whole roof

A steeper incline increases surface area for the same horizontal footprint. It can also affect installation access, fall protection arrangements, and labor costs.

Steepness alone does not establish snow capacity or guarantee that snow will slide away. Structural design, roof covering, temperature, and local conditions also matter.

For homes in the Pacific Northwest, discuss drainage and flashing details alongside material selection. Columbia Windows offers roofing installation and replacement, allowing homeowners to discuss the measured slope when requesting an estimate.

How to determine roof pitch with a calculator

Online tools can convert measurements quickly, but their input fields differ. Some request rise and run, while others accept an angle or an existing ratio.

If you search “how to determine roof pitch calculator”, choose a tool that clearly labels its inputs and units. Check whether its output shows rise:12, °, or %.

  1. Select the input: Choose measured rise and horizontal run, or select angle conversion if you already have a degree reading.
  2. Enter matching units: Supply both distances in the same unit unless the tool explicitly converts them.
  3. Check the result: Confirm that a 6 in. rise over a 12 in. run produces 6:12, approximately 26.57°, and 50%.
  4. Save the details: Record the inputs and result with the relevant roof section so they remain useful during estimating.

Calculate separate planes individually when a house has dormers, additions, or different slopes. An average can conceal a shallow section with different material requirements.

Area estimates need more than pitch alone. Overhangs, valleys, penetrations, and cutting waste affect quantities, so have the final material order checked against the complete roof.

Frequently Asked Questions

Divide rise by horizontal run, then apply arctan in degree mode. For example, arctan(4 ÷ 12) gives approximately 18.43°.
Ratios from 4:12 to 6:12 are common residential examples. The predominant choice varies by location, house style, and construction period.
Everyday usage often treats them as interchangeable. Traditionally, slope compares rise with run, while pitch compares rise with the full span.

Related Homeowner Guides & Articles

Located in Vancouver, Washington

Best Window Replacement & Exterior Remodeling Services in the Pacific Northwest!

Located in Vancouver, Washington

Best Window Replacement & Exterior Remodeling Services in the Pacific Northwest!

Get Your Personalized Estimate

Pricing depends on how many windows you’re replacing and the type you choose.

But thanks to our factory-direct model, you’ll get premium windows at unbeatable pricing.

No Middleman = No Markups

By clicking on the button you agree to our Privacy Policy